Last updated on July 20th, 2023 at 07:21 pm
Normally your vehicle computer will inform you by flashing the airbag warning light on the dashboard whenever there is are issue vehicles airbag sensor and when the airbag has an issue.
Whenever this light is turned on, it simply shows that your airbags are deactivated or wrongly connected and maybe this is taken off.
This also means that in case of an accident, the airbags will not deploy correctly or may not even be deployed at all when you get into an accident.
In this post we are going look at what causes Mazda 6 airbag light flashing continuous, the meaning of Mazda 6 airbag light flashing code 22, if or will disconnecting battery reset Mazda 6 airbag light code 22, cause of Mazda 3 airbag light flashing codes and finally the cause of Mazda cx-5 airbag light flashing code. With those in mind let get into the article fully. Read this also Guide On VW Airbag Light Reset Without The Tool
What Is the Cause Mazda 6 Airbag Light Flashing?
1. A Depleted Airbag Backup Battery
Sometimes a depleted battery could be the cause of your airbag light flashing continuously. So if you notice that your car’s battery is drained, it means that it might have also depleted the backup battery which powers the airbags.
This might correct itself after the battery is fully charged, but in case this is not the issue, then the backup battery will need to be recharged along with a sensor reset.
2. A Faulty Sensors
Note that your car has many various sensors connecting to different components. These sensors link directly to the vehicles computer system to observe and notify you when there are any potential issues. Sometimes sensors can fail or be tripped during an accident which will then make the airbag warning to be flashing.
3. A Damaged Airbag Clock Spring
Remember that the duty of airbag clock spring is to keep continuity between the driver-side airbag and electrical wiring of the vehicle.
The airbag clock spring coils in and out as the steering wheel turns. Due to this, it can become worn out as time goes, which causes a potential airbag failures and poor connection.
4. Wet Airbag Module
In case your car has had water damage before, this might have affected your vehicles airbag module that can be found under passenger or the driver seat.
This means that once it is shorted out or corroded, might not work properly.
Note that whether the airbag light is flashing by mistake or by one of these common causes, the airbag warning light was put there for a reason.
So in case, it is flashing, just get your airbag system and sensors checked as soon as possible.
Meaning Of Mazda 6 Airbag Light Flashing Code 22
The code 22 simply means that your vehicle safing sensor output is short to your car battery voltage, and on the other hand code 23 means that the safing sensor input feed of your car return circuit is open while code 24 shows that the output feed of your safing sensor is open.You should note that it’s vital for you to understand all these codes so that you will be able to get the appropriate airbag repair services needed.
Will Disconnecting Battery Reset Mazda 6 Airbag Light Code 22?
Most time all you need to get rid of this warning light is to reset your airbag sensor.
You can just remove the terminal clamp, leaving it disconnected for about 5 to 10 seconds so that the airbag sensor can reset.
Once this happens, you can then reconnect the battery terminal and then turn your vehicle on. One you do this, the light will stay off.
Mazda 6 Airbag Recall
The Mazda North America Operations is now recalling certain model of their vehicle such as the 2006 to 2007 Mazdaspeed6, 2003 to 2008 Mazda6, and the 2004 MPV vehicles.
The Mazda Company will notify all owners, and dealers will change the front passenger air bag inflator with an alternative inflator. Please note that this replacement is free of charge.
Causes Of Mazda 3 Airbag Light Flashing Codes
I don’t have to talk much on this. As you already know, this is a serious problem that you will need to get rid of quickly for the safety of your passengers and that of yourself.
However, there’s chances that your car airbag light is illuminated by accident which probably needs to be reset.
If this isn’t the case, then there are a lot of other things that might cause the airbags to fail which are:
- A Depleted Airbag Backup Battery
- A Faulty Sensors
- A Damaged Airbag Clock Spring
- Wet Airbag Module
Mazda 3 Airbag Light Flashing
It is true that your vehicle will inform you by flashing the airbag warning light via the dashboard when there is are issue.
Whenever this light is turned on, it simply shows that your airbags are deactivated.
This also means they will not deploy correctly when you get into an accident.
Mazda 3 Airbag Module Reset
You can reset the SRS light in different ways, and in each of them, you might be more involved. Below are some, in order from simple to mildly inconvenient:
- By turning the ignition key from “Off” to “ACC” position for about 10 times
- Examining/replace related fuse (you can find fuse list in owner’s manual)
- By disconnecting negative battery cable for about 10 minutes, and then reconnect
However, if after doing this and the light continues to come back on, it means you should consult a certified mechanic for inspection.
Mazda Cx-5 Airbag Light Flashing
In case your car airbag/seat belt pretension system warning light is flashing and the front of the passenger airbag deactivation OFF indicator light is turning on, then note that this can only happen if the sensors have a possible malfunction.
Once this is your case, then the front passenger-side airbags and the seat belt pretension system will not deploy properly.
Mazda 5 Airbag Light Codes and their meaning
You should note that code 12 simply means your battery voltage is very low, and while 13 shows that the airbag circuit is shorted or grounded.
The code14 tells you that the short or ground is on the primary crash sensor circuit.
Make sure to examine if your airbag is mounted very well to your car if you read code 21. While code 22 shows that the output of safing sensor is low to the battery voltage, and the code 23 tells you that the safing sensor input feed or return circuit is open.
Code 24 notifies you of the output feed is open. While codes 32 to 35 involves the issues with the airbags located on the driver and passenger sides.
Codes 41 to 45 involves the issues with the RH and LF primary crash sensor. Note that airbag diagnostic codes can go up to 53.
You should note that it’s vital for you to understand all these codes so that you will be able to get the appropriate airbag repair services needed.
Conclusion
Note that whether the airbag light flashing by mistake or coursed by some common causes note that the warning light is there for a reason.
It’s there to notify you of any danger, just get your airbag system and sensors inspected as soon as possible.
Related Article:
- Is It Illegal To Drive With Airbag Light On
- Can You Sell A Car With Deployed Airbags
- Does a Mass Airflow Sensor Need to be Programmed After Replacement
Hi dear, my name is Jeffery Ekweghi, and I am a certified mechanic and autobody parts technician. I created this site to share my expertise and experience with car lovers looking to resolve their car-related issues. I am certified in private cars and heavy-duty commercial vehicles. I have worked as a mechanic since 2015 and have experience in vehicle brands like Subaru, Jeep, Toyota, TATA, BMW, Mazda, Honda, Nissan, Kia, TVs, and Others; however, I primarily specialize in Toyota vehicles.
