Last updated on July 20th, 2023 at 07:22 pm
A Chrysler is a luxury sedan created for reliability speed and strength. It is usually not within the budget of a lot of folks but it certainly packs a punch in the driving experience.
This article will focus on the Chrysler 300, Ram 1500, and Chrysler 200 model whose engine is based on the W210 generation Mercedes E-class built between 1995 and 2003.
The Chrysler 300 is a full-size luxury car manufactured by Stellantis North America. It is a four-door sedan and has very classy designs.
You may have seen one of them without knowing. The Chrysler is a very good vehicle to drive. So good that the National Highway Traffic Safety Administration gave Chrysler a 4.0/5.0 rating for overall safety this year. Cool stuff right? How To Service Electronic Throttle Control (Ram 5500, 2500 & Ram 3500)
We are going to consider how to reset electronic throttle control manually for Chrysler 300, what causes an electronic throttle control problem for Chrysler 300, where the Chrysler 300 throttle position sensor is located in a car, what it means when the electronic throttle light comes on and what causes an electronic throttle control problem in a Chrysler 300.
The Chrysler 300 is a modern car that contains an automatic transmission system, this means that it does not have a manual gearbox and possesses an electronic throttle. This has both negative and positive implications.
How to Reset Electronic Throttle Control Manually Chrysler 300, 200 & Ram 1500
The recommendation is that you perform a throttle calibration when the throttle is unresponsive or slow. You can do this by following the steps below;
- Insert ignition key and turn the key to “ON” not start.
- You need wait for all dashboard light to go off. The check engine light may remain on.
- Now gently depress the accelerator pedal completely to the floor
- Slowly release the accelerator until it is back up all the way.
- Turn the ignition key to “OFF”.
- Then restart the car engine again.
The throttle calibration can be pretty useful when you have no idea what is going on and have to go somewhere fast.
Throttles used to be connected to the car pedals with wires. But with the advancement of technology, physical linkages have been replaced with sensors and actuators. This system allows the car to have better fuel economy and engine performance, however, if there is a problem with the throttle sensors you can lose control whime driving. Fixing this type of fault is far more complicated than reconnecting broken wires in the old days. It is safer to drive with a car having an electric throttle sensor but more expensive to fix.
What does it mean when the electronic throttle light comes on?
The electronic light comes on when the throttle system is faulty. The throttle system comprises of the throttle body itself, the accelerator and sensors. The lights may come on when the system is running checks to see if everything is alright. When it is done, it goes off.
However if the light stays on, then there is a problem to resolve. One of the ways t troubleshoot is to use an OBD-II Reader. With this tool you can find out with 100 percent certainty what the issue is. Alternatively you can call a professional to check with their own tools and let you know what the problem is.
What causes an electronic throttle control problem for Chrysler 300?
Different related problems can lead to an electronic throttle problem. However, one of the simplest way to know which part is giving issues is to read the diagnostic codes. The code readers will tell you the reason the code appeared.
It can be one of the following;
1. A faulty throttle control sensor
In a modern throttle system, when one control sensor goes bad, the entire throttle system stops working. It is just like in the Chainsmokers song “Paris” where they kept singing; “If we go down, we go down together.” Funny stuff. When it happens, you may be stuck, the good news is that the Throttle light will inform you so that you can do something about it.
2. A faulty accelerator pedal position sensor or module
The electronic throttle has a lot of sensors that send signals in the form of flashing dashboard lights. The accelerator pedal position sensor’s job is to send the current position of the accelerator pedal to the control module.
Once any of these components wear out or get faulty, a flashlight will be displayed on the dashboard. Once you see this, know that it means the system will not work properly.
3. A stuck throttle body
The throttle body is the major component in the throttle system. Once the body gets stuck, the system will malfunction. When this happens, you should call an expert to better understand but what has happened and why.
You can open and close the throttle body and check for any visible obstructions.
Electronic Throttle Control Chrysler 300 (Electronic Throttle Control Warning Light)
So, when it comes to the Chrysler 300 electronic throttle control warning light reset procedure; you can actually do this part yourself without resorting to a mechanic or seeking the help of one. In you want to do it below are some of the steps you need to take and these steps can be applied for Chrysler 300 red lighting warning light reset too. The below is also how to reset electronic throttle control manually ram 1500. And here are the steps to follows;
- Insert ignition key and turn the key to “ON” not start.
- Wait for all the dashboard light to go off. The check engine light may remain on.
- Slowly depress the accelerator pedal all the way to the floor
- Slowly release the accelerator until it is back up all the way.
- Turn the ignition key to “OFF”.
- Then start the engine again.
Yes, it is exactly the same steps with throttle recalibration. When you have done this though, the system resets and starts showing lights for only the problems that persist in the car.
Always check your dashboard for warning lights before you drive off in the morning. It can save your life.
Driving is as common as walking all over the world today but it is a very risky activity as well. Every driver has to be alert and servant. It is not only the road that holds danger, the car too can be dangerous.
How to reset electronic throttle control manually Chrysler 200
Normally the red light bolt-on your dashboard is an indication of a problem within the electronic throttle control unit of your vehicle. This sometimes may be due to a slight glitch in the system or for some other reason. To get this resolved you reset the throttle control unit.
These are almost a similar step with resting the Chrysler 300 but little difference to reset your Chrysler 200 electronic throttle control manually simply follow the steps below:
- Start by inserting the car ignition key to turn it to “ON” point make sure not starts the engine at this point.
- Now hold few seconds on for all warning lights to go off. In most cases you might notice that the check engine light will stay on
- Now gradually let go of the accelerator pedal till it is totally rested.
- Then turn off the ignition key to off point. Now start your engine and see if the throttle will throttle up as you start the car engine.
- The check engine light may remain on. Slowly depress the accelerator pedal all the way to the floor. Slowly release the accelerator pedal until it is all the way back up at the rest position. Turn the ignition key to “OFF” position. Start the engine and test the throttle by see if the engine will throttle up.
Mind you if your car battery is disconnected you have to repeat this procedure multiple times.
If this step does not solve the problem I will recommend you seek the services of a professional
How to reset electronic throttle control system Dodge Charger
Please watch the video above for dodge electronic throttle control reset for an easy step-by-step guide on jeep electronic throttle control reset that will work for almost all the models of jeep.
- So first step to recalibrating or resting the dodge charger electronic throttle control system is to:
- First get to the mopar & turn on the challenger. Let it on the “ON” position.
- Now wait for all warning lights to go out. At this post check engine light might stay on.
- Next gradually depress the accelerate pedal down to the floor completely.
- Then turn ignition to “off” point. You have to repeat these steps multiple times if it didn’t work the first time. Otherwise reach out to a professional to do this for you.
These steps is also how to reset electronic throttle control manually ram 1500 and others.
how to fix electronic throttle control jeep compass
Time to learn how to fix electronic throttle control jeep compass (Dodge Ram). Once you learn the symptoms and the reason, it will be easier to go through the solution.
You do not need to worry if you have another type of truck engine this basically will apply to most engines.
Without too much pretense, here is steps to fix electronic throttle:
1. Clean your throttle body /cover
As mentioned above, rust is one of the most common causes of the malfunctioning of an electronic throttle body. The solution is to thoroughly clean the rust.
If the body is covered with rust, the engine valve will not move properly and will prevent air from entering the engine. Of course, this is what leads to problems.
It is often recommended to use throttle body detergent or stainless steel or rust remover. See this one here on Amazon.
2. Connect Everything back together
In some cases where there is no physical damage, rust or corrosion, but you notice loose cables or sensors. Then the answer, of course, is to reconnect back together with the disconnected cables and sensor then check to see if the system has started working as it should work.
You usually see sensors near your body. It is important to verify that everything is properly connected and connected.
One way to make everything work better is to remove the sensor from the lock, clean it, and plug it back in. Make sure there are no loose cables. This could solve the problem.
3. Change or Replacement the Hose
If the test the throttle body and sensor cables but all thing seems to be good, then you can also look at the boxing problem and hose pipe issues.
This hose pipe is what connects the car engine computer to the system of the throttle. If it stops working normally the throttle systems bear it.
First, just check if it’s connected correctly (you can check if there are free ends or any lost connections).
In some cases, the host may be leaking because it broke somewhere so you need a check for that, and then you need to replace it with another one.
If none of the steps above seems to help fix the electronic throttle control jeep compass problem, then you most likely will have to replace the throttle system completely by yourself or by a professional.
Please watch this video to see the steps clearly.
how to replace electronic throttle control system
1. Find your car Throttle Control
And if you have no idea where the slipped body is or what it looks likes, just don’t worry, it looks like a pump and connects directly to the throttle sensors and air filter. You will find it at the top or near your engine.
On most trucks, it is covered in plastic or metal cases. So when the cables and pipes come out, a little box looks like the part.
2. Remove the throttle body
To proceed to the next step with the replacement; it is necessary to use a screwdriver to disassemble everything. In some cases, you will need a wrench tool kit like this one here on Amazon.
Either way, loosen and gently remove the cap. This releases the body from the throttle.
3. Unplug everything
Then proceed to unplug everything. This includes the hose that connects the air filter and the sensor cables on the other side. Then proceed to disconnect from the rest of the body by removing the bolts. You may need a key for this. Finish off by removing the throttle body.
4. Install the new body
With room for the new body throttle intake, you should have no trouble setting it up.
If you have the correct body throttle, it will take 5-10 minutes to set it up. Follow the same transfer process, but in reverse.
Then tighten the bolts, reconnect the hose, cables, and replace the cover. Then you are done. If you need help setting up the slippery body, we applaud you watch this video here:
Jeep Compass throttle body replacement video
FAQ on Jeep Electronic Throttle Control Reset
How do I reset my electronic throttle position sensor
- Start by releasing your accelerator pedal completely
- Now turn your ignition key to off after you turn it off
- Wait for 5 to 15 second for all the lights to go off.
- Make sure your throttle valve is moving, listen for sounds of operation during the 5 to 15 seconds wait period.
- Now turn the ignition key to “OFF” position and start the engine and test the throttle by see if the engine will throttle up
Can you drive with a bad electronic throttle control
The simple answer to this question is yes. You can drive your car even when the electronic throttle control system is bad and faulty but I will not advise you do that because if your car electronic control sensor is bad, your vehicle will not operate at it optimal state and as result; it makes it unsafe you the driver and your passengers too. Also driving with a bad electronic throttle control sensor can cause damage to other systems and parts of your vehicle which result in more expensive repair cost. So I will advise you to fix bad electronic throttle control issues as quickly as possible before it escalates.
Besides, any trouble codes that your bad throttle position sensor may have triggered to be sent to your engine computer had to be resolved and cleared completely. Otherwise, your car will not pass a US smog inspection test if needed. You also will find it difficult to sell your car be it to a an individual or dealer. So basically driving with a bad throttle position sensor is not a good idea at all; you should have a bad throttle position sensor fixed immediately you noticed the issue.
Please watch the video above on Jeep Compass throttle body replacement
How much to fix electronic throttle control?
On average a car throttle control body cost around $200 and above while some cheaper and affordable models can cost low as $100 and in very rare cases less than $100.
And if you are taking labor to a repair shop, it will cost you around $50 to $300 on average depending on the level of damage the ETC system has. But if you are going to repair or fix the electronic throttle control system (ETC) yourself, then you won’t need to spend this additional labor cost it will just be the money for buying the ETC unit.
Should I take my Dodge RAM to a repair shop?
If you have tried any of the fix steps above for your dodge ram and find no result, then you should take your car to a repair shop after you have tried replacing the ETC electronic throttle control by hand yourself first.
